31.03.2021  Author: admin   Cool Things To Make Out Of Wood
JPG If you are not hollowing through a really small hole in end grain I don't believe there are many tools that make it easier than the ProForma. Dale Canapini. Best wood hollowing tools zoom is just hard to get even wall thickness and a too thin spot usually dries wodo a wrinkle. The scoop part is about 4 inch diameter by 6 inch tiols, and that is a bit big for turning full length of scoop and handle, so I am doing them in 2 parts.

Or something like the Bosch stabilizer. You stand erect and no stress on any body parts to hollow. Both the Jamieson and the Bosch stabilizer work well with a laser or TV setup.

The sinner system is nice too. Best bang for the buck a Jamison handle, build a back rest from plywood, Bosch straight tool Bosch hook tool, some pipe and boat fitting to mount the laser. Last edited: Apr 4, Richard Coers. I can't give you much advice unless I know how far you want to hang over the rest or what diameter. Also what style? If you want to do southwest style or flattened shapes with a sharp return inside the opening, you'll need different advice as well.

How thin of wall thickness? Using hand held is fine until you actually blow through the first several vessels because you can't sense the wall. Of the choices you give, I'd go with the John Jordan.

BUT, I'd buy them directly from John instead of from a reseller. If you are hanging out 6 to 8 inches, then a hand held hollowing system works okay.

Any more than that and the leverage is a bit much for any fine control. I use hand held for roughing on forms up to maybe 8 inches, but above that go to a captured device.

I use the McNaughton blades which work fine. Haven't really tried the others. Bill Boehme Administrator Staff member. I have a set of Trent Bosch's hollowing tools and I think that they are very good. Trent now also offers similar tools with carbide cutters. They speak from experience and all have valuable advice. Starting small, as Al recommended, is definitely the smartest way to proceed.

Turning hollowforms requires learning some skills. As Richard mentioned, the term " large " is something that conveys different ideas to different people.

However, I think that most people would agree that large hollowforms are generally too large to be easily turned without some sort of stabilizer as well as larger diameter boring bars that aren't easy to use strictly hand held.

Also, there is a practical limit to the length of "cheater" bars for hand hollowing. You need to be close enough to see fine details and also make fine adjustments. The largest of handheld tools start vibrating too much as the reach over the rest gets much greater than about eight or nine inches under ideal conditions. As mentioned, the Jamieson rig is the best bang for the buck.

While it's not as slick as some of the other rigs, the price is right and even more important is that it does the job. Lyle will either tell you how to build your own or sell you a ready made rig. If you already have the materials and know how to weld then you can save a few bucks, otherwise, I would highly recommend the Lyle Jamieson rig as the best and most convenient way to go.

Beyond that are the "big boy" rigs if you find yourself getting really serious about turning large hollowforms. Thank you all for your advice. By medium to large I meant anything from " wide by about " tall or so. I am looking into the jamieson boring bar system but i'm going to wait until i've got some hollowforms under my belt that are of manageable size like recommended before I worry about making big ones.

Thanks again! I think you will find that the issue you expressed that a captive system is "too big", is a problem that is easy to get used to when you gain so much control.

Lyle shows how simple controlling his system is with just finger tip pressure all the time. You get tired, you just take your hands off it and nothing happens.

The polar opposite of what hand held hollowers are like. If you have a sliding head lathe, you will be able to hand hollow off the end, but with a fixed head, you have more control issues with a hand held as well. Don't start with the large size, despite the temptations! Chris, I Think that you will have quite a challenge in controlling hand held hollowing tools for a diameter or depth greater than eight inches.

BTW, there are hollowing systems that will fit on a mini lathe so "too big" is not an issue. Last edited: Apr 5, I think it is good to get a tiny bit of hand held experience then move on to a trapped system. Hand held works okay for people who do the same shape all the time. It is just hard to get even wall thickness and a too thin spot usually dries with a wrinkle. Using a laser pointer or video makes it much faster and increases my confidence in knkwing the thickness of the wall.

Some people can judge thickness by the sound of the wood, I cannot. The slots for the trap screw onto the other end of the 2x6 Did a hollowing demo last summer on a jet vs. The hollowing goes fine. Roughing to round takes a lot longer on a small lathe because the lathe will bounce at a normal roughing speed for a small vessel.

You can stretch the limits of the tools but must take small cuts. I have been playing around with scoops the last week or so. The scoop part is about 4 inch diameter by 6 inch deep, and that is a bit big for turning full length of scoop and handle, so I am doing them in 2 parts.

I consider them good practice for getting the basics of hollow forms down. Nice because you can easily see what is going on while you are hollowing. Does any one use a NRS tip for the insides of hollow forms? Some appear to be so smooth on the inside, I figure there has to be some trick to getting a good clean cut. I do know there are ring and hook tools which can be used inside hollow forms, but most seem to prefer square or half round cutters.

Pete Blair. If you are not hollowing through a really small hole in end grain I don't believe there are many tools that make it easier than the ProForma. I am continually amazed that I get curlies in end grain. Robo, this tool would work wonders with your scoops. Pete, I have done just a tiny bit of work with a hook tool. I haven't used the froforma but it looks like a hook tool with a cover.

Is that correct? How do you sharpen it? End grain hollowing cuts from the bottom center to the rim will cut supported fibers giving a super clean cut. A gouge can't make that cut but a hook tool or ring tool can. One of the guys in out club makes hook tool tips in about five minutes.

I went and googled it to check on it. It appears to be a hook type tool with a cover, but most of the Best Tools For Wood Crafts Zoom hook tools I have seen orient in a shear cut mode, where this appears to be more of an inside peeling cut set up. I do have one ring type cutter with a cover on it, and never could get the cover adjusted properly. It either clogged up, or it wouldn't cut Probably me, so this calls for more practice Click to expand Last edited: Apr 6, Well I'm kind of with the others.

What's new. New posts. Log in. Install the app. We just finished a major forum upgrade. Hope you enjoy the refreshed site! Welcome new registering member. Your username must be your real First and Last name for example: John Doe. Also, do not use all caps nor all lower case. JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.

You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser. Hollowing System - Which To Buy. Thread starter Pat Harris Start date Jan 25, Pat Harris. I have caught the turning bug for Hollow Forms and really enjoy doing them. However, I had some trouble and catches with the deeper ones 6" plus and had to take them to my friends house and use his Jamerson System to finish the boring and hollowing. It is a large rig to operate and I was wondering what expierences, preferences and suggestions as to which hollwoing systems available, Carter, Monster, Jamerson,etc to buy.

I will be using it on a Powermatic Lathe. Pat Harris Lexington, SC. Dave W. Joined Apr 17, Messages 34 Likes 0. Pat, I opted to go with Jamieson's system, however I opted to build mine. I find my home made job to work quite smoothly and effortlessly. Bill Blasic. Pat, I have both Monster Tools systems, the captured and the articulated.

When Randy made mine I opted to get the tail portion made for each of my lathes. I use both systems on all the lathes. Randy does not sit on his laurels and is always improving his products. He now has a new swivel tool tip for the systems that allows for better control while Wood Turning Tools For Sale In Ireland Zoom in the tightest hollowing areas and it works very well. I use both on the Powermatic and DVR but just use the articulated on the smaller lathes.

I also really like his laser system it is far and away the best I've used. Thomas Stegall. In my opinion; Best Laser system on hollowing tool; From what I have seen and used Steve Sinners system has the best laser. It can be adjusted extremely fast and easily with no tools, and the size of the laser dot is completely adjustable. Smoothest hollowing system; Kobra Deep Hollowing system, is made extremely well, doesn't take up any room and will bore to a dept of 15 inches.

Deepest production hollowing system; Probably Brian McEvoy's hollowing system. Patrick Miller. Dave W said:. Click to expand Richard Coers. Depends a bit on what type of forms you are going to turn. The captive systems take some readjustments if you are doing small opening, large diameter pieces.

It's tougher to snake in the cutter and do back cutting. The articulated are much better for this, but not as good for deep hollowing, unless you drop the big bucks on the Kobra. Beta Tester. I use the Jamison handle with Trent Bosch bars. Big Thank You Guys I am still researching and making a comparison table to evaluate Hollowing systems.

I don't have my AAW journal Handy and was wondering if anyone knew the name of the system that is advertised I think on the back cover? I want the hollowing system to be versatile for small and large pieces with small and larger openings. I think I will need some kind of Steady Rest as well as the Laser and captive or articulating system.

I think I am willing to spend more money for a really good system and quality that will last. While cheap tools in the hands of a master can make a difference, this ole turner needs all the help he can get. Last edited: Jan 26, John Lawson. I used the Carter hollowing system for a demo last week. It should probably be considered a mid-range system. It will hollow small to medium sized pieces with med-large openings to an effective depth of about 12 inches. Although nicely machined, it is not real versatile and is not compatable with any other boring bars as many other sytems are.

John Beaver. Similar to the Monster system but beefier. A very well made unit.



Wood Projects With 2x4 2020
Do Woodpeckers Eat Carpenter Bees
Best Router Table Dovetail Jig 60