12.12.2020  Author: admin   Wood Gifts You Can Make
Drill the holes right through the bench top and bolt the vise into the top. The instillation covered here is for a cast-iron vise with the groz woodworking vise installation windows jaw butting against the edge of a top. Manufactured from close-grained grey cast iron, this robust vise has accurately machined housings for smooth sliding and true parallel action, free of side or cross movement. Shop Talk. Steel main screw has buttress threads for groz woodworking vise installation windows, accurate and responsive adjustment. Popular Articles. Glue the block to a hooked standoff that registers against the edge of your bench as shown in the photo.

Home Articles Installing a Bench Vise. This article is from Issue 41 of Woodcraft Magazine. Vises provide the muscle for securing workpieces for planing, sawing, routing, and other tooling operations.

Similar vises may differ in features, but attachment is similar. The first is a simple approach, perfectly appropriate for an end vise application. The second involves recessing the rear jaw flush with the edge of the bench. This is the best approach for a face vise, because the entire length of a board secured for edge work will contact the bench edge for support and additional clamping, as shown in the photo above.

Regardless of the type of mounting, have your vise s in hand before you start so you can determine the size of the spacers, jaws, and hardware needed for a trouble-free installation. Face vises are attached on the front, or face, of the bench; end vises are installed on the end. Southpaws will want to do the opposite.

Shift the top if necessary to accommodate the vise. Because a face vise is used for general work as well as for planing edges, I recommend investing in a larger vise at least 10". The easiest installation entails making spacer blocks to set the tops of the metal jaws below the bench surface while screwing the vise to the underside of a bench.

To begin, drive the roll pin from the end of the vise screw, remove the connecting bracket and the front jaw, and then degrease the vise of its Yost Woodworking Vise Installation 3d protective coating. To determine the thickness of your spacer blocks, place the rear jaw upside down on the inverted benchtop and measure how much the top of the jaw projects beyond the underside.

The former is necessary for better dog height on the smaller vise. Countersink the holes in the rear jaw Photo A , and then attach the rear cheek with flathead wood screws and the front cheek with roundhead screws and washers. Make your spacer block s. Use two for an end vise to provide dog clearance.

Plane them to your determined thickness, and size them in length and width to suit the mounting hole surfaces on the rear jaw bracket, as shown in Photo B. Sandwich the blocks between the bracket and the bench, trace the locations of the mounting holes, and drill clearance holes through the spacers. Reattach the connecting bracket, washer, and roll pin. After turning the benchtop upright, hand-plane the tops of the wooden cheeks flush to the benchtop. Because most vises include an integral dog, it makes sense to incorporate a row of dog holes into your benchtop.

Glue the block to a hooked standoff that registers against the edge of your bench as shown in the photo. Make sure to align the hole with the dog on your vise. Draw a centerline down the rear face of the block for positioning reference. Use a square to lay out the dog hole locations on the bench, spacing them 6" apart starting from the end of the bench. Guide a circular saw along a secured straightedge to rip the length of the notch up to the crosscut.

A flush-mounted face vise offers the most versatility, but it requires more work to install. As with the previous method, handling is easier with the vise disassembled. First, lay out the notch in the benchtop. Its length should be the width of the jaw plus 1". Make the crosscut into the benchtop edge with a backsaw.

Then clamp a straightedge to the bench to guide a circular saw to cut the length of the notch. Rip the notch until you intersect the previous crosscut Photo C , and then finish up with a handsaw. Attach the rear cheek with 10 flathead woodscrews after countersinking the holes in the jaw. Center the block along the width of the notch, with the edges of each aligned flush at the front. Clamp the block in place, and then attach it to the benchtop with lag screws and washers, as shown in Photo D.

To make the wooden cheek for the rear jaw, first measure the thickness of the jaw. Crosscut the piece and bandsaw the interior to make the U-shaped cheek filler. Then crosscut it to fit the benchtop notch. Countersink the holes on the rear jaw and attach the cheek as shown in Photo F.

Position the vise on the spacer block with the cheek nestled in its notch. Mark and drill pilot holes, and attach the vise with washers and lag bolts Photo G. Use a straightedge to ensure the face of the jaw is flush with the edge of the bench.

Make the front cheek, and attach it with washers and roundhead woodscrews, reassemble the vise, and turn the benchtop over. Hand-plane the cheeks flush with the benchtop Photo H. My bench had radiused edges, so I chiseled away the sharp point at the corner of the cheek. You are likely to need a filler block between Groz 7 Woodworking Vise 20 the bench underside and the mounting bracket portion of the vise to to produce the intended spacing.

Install the filler block for the vise. Drill and counterbore the block for 4 lag bolts before securing the block to the underside of the top. Drill the pilot holes while the block is positioned on the benchtop, add glue and thread the lag bolts home. Position the vise on the block with the back jaw against the edge of the bench. Drill the pilot holes and add the lag screws.

Make wood faces for the jaws so that pieces you are working on will not be damaged by the cast-iron jaws. Just screw a rectangular piece of hardwood to each of the jaws. Most jaws have predrilled holes which makes the job easier.

If you took apart the vise while mounting it, put it together again now. We welcome your comments and suggestions. All information is provided "AS IS. All rights reserved. You may freely link to this site, and use it for non-commercial use subject to our terms of use. View our Privacy Policy here. Toggle navigation subscribe. Installing a Vise on a Woodworking Bench. Written by Doityourself Staff. What You'll Need. Cast-iron vise. Drillwith wood bit.

Lag bolts. Step 1—Choose Where to Put your Vise A vise will usually be best situated near a corner as many other places will either be in the way, or will be impractical when working with long- or odd-shaped items. Lag Screws vs Wood Screws.

How to Measure Lag Screw Length. Related Posts Work Bench materials. Read More. Basement Shower bench waterproofing. Hi Everyone, This will be my first time installing tiles and shower benc I have a question I'm hoping someone can help me with because I can't seem



Table Top Wood Carving Machine 65
Undermount Drawer Runners Hafele Work
Woodwork Project For 11 Year Old Uk
Diy Wood Projects Without Power Tools Free