24.02.2021  Author: admin   Wood Gifts You Can Make
Small adjustable stand - this can be made from wood or metal. Here is one example of how to put together a wood bench grinder stand. Find the center line of the 2x8 and glue, then screw the two pieces of 2x4 along the length grlnder it. Share Pin. Just design to fit your how to build a wooden bench grinder stand quote while keeping the bench grinder secure, stable and at comfortable heights. The other key is that ti deck of your stand is large enough to hold your bench grinder comfortably. Wall bracket stand - this uses a steel wall bracket, steel arm with a pad big enough to hold your bench grinder.

This allowed the builder to construct simple pull out shelves for small tools and other bench grinding items. A bottom shelf was stationary and helped provide support for the walls and bench grinder. Underneath it all were sturdy lockable wheels that could withstand the weight and the stress of grinding. Innovation coupled with common sense allows you to build a bench grinder stand with wheels.

How to do this depends on the type of material you use. Metal stands are a little bit different from using wood and takes a different skill set to put together. Here is one example of how to put together a wood bench grinder stand. It is a very simple design and should not take you a long time to build. You first cut the 4 by 4 beam to the height you want your bench grinder to sit at. Make allowances for the deck thickness.

Cut a long piece of 2 by 4 into 30 cm lengths. Cut off one corner of those small pieces but do not throw away those wedges. You will need them later. Glue and screw those 30 cm pieces to the 4 x 4 post. This should give you a very stable base. Cut an appropriate size deck from plywood and mark where the top of the beam will sit.

Pre-drill your holes to attach the bolts that hold the deck to the beam. Glue and screw the deck to the beam. Then take those leftover wedges and glue and screw them to both the beam and the deck. This is your deck support. Flip it over and you are done except for any painting or staining you want to do. That is it. If you want to go more elaborate and be more creative then you will need to factor in more materials and their cost. You will also need to add in a lot more time.

It all depends on you. There are few regulations governing a DIY bench grinder stand. You are not stuck to attaching your bench grinder to your traditional workbench. Besides you may not have one or you do not have enough room on it to place your grinder.

That is where being innovative can come in handy. You can design your own bench grinder stand and be as simple or as creative as you can be. Just design to fit your needs while keeping the bench grinder secure, stable and at comfortable heights. So at this point you should have something that looks like a steel I-beam with the top surface being wider than the bottom.

Now take your legs, either 2x4's or 2x6's or what have you and drill some pilot holes. You essentially need to butt the legs up into the top of the stand, and as they extend downward they will all follow the same angle as they pass the lower surface of our "I-beam". Add some more glue and screw the screws in place- two people may be better as one can hold the leg from falling while the other screws it in place- you can also hold it in place with your foot like I did.

Now at this point you've got your self a pretty heavy duty saw horse. If you use this method with only 2x4's then they will be nicely stackable and therefore easy to store if your workshop isn't crazy huge. My bench grinder was an old beast from my grandfathers work shop they don't make em like that any more , and when he gave it to me it came complete with rubber washers and lag bolts to secure it to a bench and minimize vibration.

I just placed the grinder, marked the holes in the base, then drilled some pilot holes to accommodate the lag bolts. In the side views you can see that I have also added some trapezoid shaped 2x6's that are screwed on to shore up the connection between the legs and the top of the stand.

I was considering adding lower cross pieces on the sides and front and back, but their are only so many hours in the day. Also, I was only using this to polish some hardware that came off of some old Miracle doors so I really wasn't planning on applying that much horizontal pressure towards the grinding wheel.

During the test run, the stand held in place, none of the joints wobbled and I was able to safely polish some brass hardware. If I plan on using the grinding wheel at some point I will add cross pieces lower on the legs and maybe throw a sandbag on said joists to improve the base weight and stability.

Overall I think the design is simple and I look forward to having a portable stand that won't ever be in the way on workbench! Cheers and thanks for reading! I'm surprosed you didn't make something you could attach to your "work mate" so it would take up less space when not in use.

Introduction: Bench Grinder Stand. By Ssmo72 Follow. More by the author:. So the materials in total include: -a 24" length of 2x8 -a 24" length of 2x6 -2, 24" long pieces of 2x4 -and 4, 33" long pieces of 2x6 for the legs -used various lengths of wood screws recovered from a kitchen demolition, they should all be at least 2" in length, preferably longer.

Did you make this project?



Make A Frame Photo Online Play
Free Woodworking Plans Pdf Files 2020
Etam Vincennes