15.01.2020  Author: admin   Easy Woodworking Projects
This band saw is designed and intended for use by properly trained and experienced personnel only. Page Width 9. An undersized cord will cause a drop jet 14 inch bandsaw manual yellow line voltage, resulting in loss of power and overheating. If there are questions or comments, please contact your local supplier or JET. Page 20 Notice the bearing holder on the shaft is eccentric. Slide blade out through slot in table.

Give your work undivided attention. Maintain a balanced stance at all times so that you do not fall or lean against the blade or other moving parts. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown.

This machine has been designed and constructed to provide years of trouble free operation if used in accordance with instructions set forth in this manual. Page 7: Unpacking - JwbsOs 3 — M5x12 pan head screws approx. Report any damage immediately to your distributor and shipping agent. Read the instruction manual thoroughly for assembly, maintenance and safety instructions. Contents of the Shipping Container Container One With the aid of a second person, lift the saw body out of the shipping container and place onto the stand top.

Page 10 7. Place motor over rubber grommets and fasten to stand top with four hex cap screws, eight flat washers, washers, and four hex nuts, as shown in item C, page 7.

See Figure 4. The arrangement of these fasteners is shown in Figure 5. Page 11 To mount table, remove table insert and table pin see Figure Orient the table so that the saw blade will pass through the slot in the table and into the center opening.

Continue holding up the table, and turn the With the aid of a second person, lift the saw body out of the shipping container and place onto stand top. Screw the two small knobs Figure 17 into the threaded holes in the saw body.

Slide the pulley cover down over the knobs, Jet 14 Bandsaw Dust Collection Editor and tighten the knobs. Attach trunnion support bracket to saw body Page Grounding Instructions To mount the table, remove pin and insert from the table Figure Orient the table so the saw blade will pass through the slot in the table and into the center opening. Continue holding up the table, and rotate the table so the two screws Page Volt Operation The band saw must comply with all local and national codes after the volt plug is installed.

The band saw with a volt plug should only be connected to an outlet having the same configuration Figure No adapter is available or should be used with the volt plug. Page Extension Cords Make sure the cord is in Jet Bandsaw Model Wbs 14 30 good condition, and heavy enough to carry the current your band saw will draw.

An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Page Changing Blades 90 degrees with the blade. If necessary, adjust scale pointer to zero. Changing Blades Blade teeth are sharp! Use care when handling the saw blade. Failure to comply may cause serious injury. Disconnect machine from power source. Loosen blade tension by turning the tension knob counterclockwise Figure Page Adjusting Blade Tracking As you become more experienced with the saw, you may find it necessary to change the blade tension from the initial setting.

Changes in blade width and the type of material being cut will have an effect on blade tension. Never operate the band saw without all guards in place and in working order. Blade must already be tensioned and tracking properly. Page 20 Notice the bearing Jet 14 Steel Frame Bandsaw Review 2020 holder on the shaft is eccentric. Index the bearing shaft to another position and slide it back in, making sure the flange on the thumb screw H, Figure 31 properly seats into the groove Jet 14 Bandsaw Blade Guides With of the bearing shaft.

Saw stops or will not Fuse blown, or circuit breaker tripped. Cord damaged. JET warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these JPW Industries Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine maintenance and major repair on your JET tools. For the name of an Authorized Service Center in your area call New Products.

Replacement Parts. Mortisers Grinders Scroll Saws Accessories. Stay Connected Be the first to know about new products, events and special offers.



Hinomaru Tombo Japanese Wood Carving Tools Knife Set Ep
Lee Valley Steam Bending Kit Youtube
Word By Word Quran Translation In Tamil Uk