22.01.2020  Author: admin   Small Diy Wood Projects
View online Operating instructions and parts manual for Jet JWBSSFX Saw or simply click Download button to examine the Jet JWBSSFX guidelines offline on your desktop or laptop computer.  Jet JWBSSFX Operating Instructions And Parts Manual. Download Operating instructions and parts manual of Jet JWBSSFX Saw for Free or View it Online on www.Woodworking Air Cleaner Brand: Jet. Category: Saw. Type: Operating instructions and parts manual for Jet JWBSSFX. Pages: Download Jet JWBSSFX Operating instructions and parts manual. 1. 2. We found 1 PDF manuals for the Jet JWBSSFX (Saw) device. Free download of Jet JWBSSFX manuals is available on www.Woodworking Air Cleaner   Jet JWBSSFX: Related Products. Jet J Jet JTS Jet JtasX Jet Hvbs-7MW. Jet J Jet Xacta JtasDX. The JET 14" SFX Steel Frame Bandsaw redefines the line between functionality and affordability. The large, cast-iron table’s square inches of work surface ensure greater workpiece support when making deep cuts. The machined aluminum fence system features easily visible measurements for the most accurate cutting. This saw is equipped with JET’s blade guide system, making adjustments quick and simple. With over 13 inches of resaw capacity, the JET 14" SFX Steel Frame Bandsaw leads its class. Dual 4" dust ports allow for maximum dust collection efficiency. The heavy-duty tubula.

Table Of Contents. Quick Links. Operating Instructions and Parts Manual. Table of Contents. Previous Page. Next Page. M Ph. Page 2: Important Safety Instructions Do not use this band saw for other than its and other substances known to the State of intended use. If used for other purposes, JET California to cause cancer. Avoid inhaling dust disclaims any real or implied warranty and holds Page 3 Check damaged parts. Before further use of Turn off machine before cleaning.

Use a brush machine, a guard or other part that is damaged or compressed air to remove chips or debris — should be carefully checked to determine that it not your hands.

Page 4: Table Of Contents Page 5: About This Manual Additional knowledge can be obtained from experienced users or trade articles.

Whatever accepted methods are used, always make personal safety a priority. If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our web site: www. Page 6: Specifications 4. Page 8: Setup And Assembly Read and understand the jet 14 sfx bandsaw manual workshop contents jet 14 sfx bandsaw manual workshop this manual before attempting assembly or operation.

Failure to comply may cause serious injury. Figure hardware package Box 1: Stand not shown 5. Only hand tighten screws at this time. Figure 5. Take measurements at both front and back of table — these should be identical. If miter slot is not parallel to blade, bump table with rubber mallet in the needed direction.

Page Storage Screw Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. Page Voltage Conversion Zero setting of cursor cannot be used with horizontal fence position. Figure jet 14 sfx bandsaw manual workshop. Remove dust block C, Figure Carefully remove blade from top wheel, then from between upper and lower blade guides and lower wheel.

Slide blade out through slot in table. Guide new blade through table slot. Place blade loosely in upper and lower blade guides. The blade performance. Tip: When the band saw is not being used, raise tension lever to release position — Page Upper Thrust Bearing 7. Refer to Figure The thrust bearing prevents backward deflection of blade during cutting.

Disconnect band saw from power source. Loosen screws M, Figure with 3mm hex wrench and raise guard plate to expose thrust Figure blade guide adjustment bearing. Page Guide Post 7. However, belt tension should be occasionally checked when the band saw is new, as a new belt may stretch slightly during the Jet 14 Sfx Bandsaw Review 10 jet 14 sfx bandsaw manual workshop in process.

Page Operating Controls gauge for a crosscut, the fence should be 8. Turn on band saw and allow a few seconds for 8. Press green button to start. Press red paddle button to stop. Page Crosscutting 9. Page Width 9. Set patterns are usually tooth. Page User-Maintenance Clean band saw regularly to remove any resinous appropriate capacity.

See our website for a full line deposits and sawdust. Keep miter slot and guide bearings clean and free Periodically vacuum out the motor fan cover. Page Blade Selection Guide Tighten lock handle. Trunnion locking mechanism is broken Replace trunnion locking mechanism. Reduce feed force. Blade pitch too coarse.

Refer to blade selection chart; use finer pitch blade. Guide bearings not properly supporting Check guide bearings for correct blade. Adjust or replace as needed. Page Mechanical And Electrical Problems Non-proprietary parts, such as fasteners, can be found at local hardware stores, or may be ordered from JET. Some parts are jet 14 sfx bandsaw manual workshop for reference only, and may not be available individually.

Power Cord Jet Logo with Adhesive Wood Insert Socket Head Button Screw Lock Washer Push Stick, Red Hex Nut Adjustable Handle Hex wrench not shown Page Electrical Connections Print page 1 Print document 36 pages. Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password. Upload from disk. Upload from URL.

Item number Description Literature; A: JWBSOS, Bandsaw with Open Stand: Manual: K: 14" Closed Stand Bandsaw, 1HP, 1Ph, /V: Manual: K. This manual is provided by JET, covering the safe operation and maintenance procedures for a JET Model JWBSSFX Band Saw. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. Nov 18,  · I sent them a at the anatomy on of lower components where there was no 3rd pulley. As well as the exploded diagram of the bandsaw in the manual. Also sent them photos of the original v-belt with the correct size and what size belt it stated in the manual. I am too far about hour and half to the closest Jet Service Center.

Making Wooden Tool Boxes Pdf
Best Router For Making Wood Signs Mat