10.08.2020  Author: admin   Fun Things To Build With Wood
This will reinforce the joint even further and prevent the boards from coming apart as you fasten them. Use pocket holes to reinforce the joints in krge favorite antique furniture kreg drill jig 60 and increase their lifespan. Co-authors: 4. Learn why people trust wikiHow. Change the placement of the jig.

Things You'll Need. Related Articles. Article Summary. Part 1 of Knowing the exact thickness of the board will enable you to drill the pocket holes at just the right angle. The difference of a fraction of an inch could potentially throw off your whole project. Set your drill bit collar to the correct depth. Line the pocket hole drill bit up with the specifications indicated on the base of the jig. The step the place on the bit where it narrows to a point should be even with the notch that corresponds to the thickness of your board.

Slide the depth collar to the appropriate height and tighten it using an Allen wrench. A special pocket hole drill bit should be included with your new Kreg Jig. Change the placement of the jig. Using the same measurements, adjust the height of the jig to the appropriate position. To do this, loosen the thumbscrew on the back so that you can raise or lower guide hole piece freely. Once the jig is where you want it, tighten the thumbscrew to secure it. Remember to reset the guide hole piece every time you drill a board of a different size.

Secure the jig to the workbench. Clamp the jig down so that it will remain firmly in place. Make sure the guide holes of the jig are facing toward you on the workbench. Part 2 of Clamp the wood into the jig. Place one end of the wooden board vertically against the clamp backing on the opposite side of the jig, then pull the lever to press the clamp tight against it.

Fit the drill bit into the guide holes in the jig. The guide holes should be just large enough to comfortably accommodate the drill bit. Most standard Kreg Jig models will have at least three guide holes so that you can drill as many holes as needed to support the joint. Should you need more pocket holes than your jig allows, you can make room for more by shifting the wood down in the clamp after drilling your first set.

Drill the desired number of pocket holes. Pull back on the drill as you work to free the guide holes of loose wood chips. Drill as many holes as you need to create a strong joint that will suit the purposes of your project, then turn the board around and repeat the process on the other end. Part 3 of Press the pieces of wood together to form a joint.

Make sure the edges are evenly aligned. If you prefer, you can clamp the boards in place to make them easier to manage. Glue the edges of the joint together for added security. Spread a thin layer of wood glue onto the edges of the boards where they connect.

This will reinforce the joint even further and prevent the boards from coming apart as you fasten them. If you're using wood glue in addition to a conventional clamp, apply the glue before you align the edges of the boards. Drill the screws into place. Drive the screws deep until they disappear inside the pocket hole.

The pocket hole bit conveniently bores its own thread as it drills, so you should have no problem getting the screws to hold. Finer threads should be reserved for hard, dense varieties of wood like maple and oak. Conceal the pocket holes with wood plugs or adhesive.

These can easily be filled with a glob of putty or wood glue. You could also invest in a set of Kreg wood plugs, which are specially tapered to slide right in for a smooth, seamless finish. Include your email address to get a message when this question is answered.

Take proper safety precautions by wearing eye protection while drilling. Helpful 0 Not Helpful 0. Kreg Jigs are useful for mounting shelves, putting together wooden crates, making your own tables and cabinets or dozens of other woodworking projects. Helpful 1 Not Helpful 0. Use pocket holes to reinforce the joints in your favorite antique furniture pieces and increase their lifespan. Submit a Tip All tip submissions are carefully reviewed before being published. Helpful 2 Not Helpful 0.

Exercise caution when working with electric drills and other power tools. It also comes with a lifetime drill-guide warranty. The Pocket-Hole Jig is the complete set of joinery tools and accessories in the Series. The comes with its own compact case to store all your accessories, which includes 40 pocket-hole screws and a clamp adapter.

Similar to the , it also has a material thickness gauge, easy-set drill bit, an anti-slip base — and of course, a lifetime drill-guide warranty. This jig sets the standard for flexibility and versatility in pocket-hole joinery. And like all Kreg Pocket-Hole Jigs, you also get a lifetime drill guide warranty. The Pocket-Hole Jig is the premium choice for project builders who want to build smarter and faster than ever.

The durable construction of the jig is strengthened by a steel-reinforced spine, plus hardened steel drill guides with a lifetime warranty. A dust collection attachment connects to your shop vacuum to keep your workspace dust-free.

The includes onboard bit storage, 60 pocket-hole screws, and a project plan to get you started building. The Pocket-Hole Jig PRO is the ultimate joining setup for project builders who want a full suite of Series tools and accessories. The Docking Station allows you to create a premium joining workstation with added storage, stability, and support. The material support wings are infinitely repositionable so you can work with longer materials without any hassle.

You can also stash bits and screws inside the material support wings, then fold them up easily when you want to stow it all away.



Woodturning Chisels Uk Europe
Fun Wood Lathe Projects List
Wood Project Ideas Pinterest Map