17.12.2019  Author: admin   Workshop Bench Plans
Using wood glue will work best. Related wikiHows How to. This will help you avoid cutting it wrong later. When the glue has dried, gently hammer in a nail at each of the four corners to secure the pieces together. Wiht it is time to put the four pieces of wood together into your frame. Frame Type.

Now we want to cut the mounting board down to OD. Be careful when handling the matt board so you don't stain it or get it dirty. If you do get a smudge on it, you can sometimes clean it off using a clean eraser.

Follow the same instructions for cutting the mounting board as illustrated. This step is perhaps the most nerve racking because if you make a mistake you have to get a whole new board. The following instructions assume you have an angled matt cutter.

Following that is a description of how one might do this with a board and box cutters. Place the matt board face down on some scrap matt board, scrap chip board or something else to protect your work surface. Scribe a line the matt actual thickness from all four edges. As with making the marks to position the picture, this is easier if a scribe is used, but it can be accomplished with a straight edge and a ruler.

The next couple of steps are those for the specific matt cutting tool I have. Read the instructions for your tool and follow those if different. Place a straight edge on the outside of the line. Position the tool so that that the center mark lines up with the line perpendicular to the edge of the straight edge. Plunge the knife into the board and pull it along the straight Make A Frame In Tkinter Quota edge until the center mark lines up with the other perpendicular line. Repeat for the other three lines.

Be very careful that the straight edge does not move while you are cutting the matt. If possible, clamp the straightedge down. I can't stress enough that the straight edge must not move while cutting. While making this tutorial I got sloppy and I messed up the first one. I actually messed up the second one a little as well but not as badly so I'll use it. The alternate method for cutting the matt if you don't get a tool will require a straight edge with a 45 degree angle and a long box knife.

To create the straight edge, use a table saw to true up one side of a board. Tilt the saw blade to 45 degrees and trim off the second side. To cut the matt, follow the instructions above to mark the lines. Lay the straight edge on the outside of the line with the 45 degree slope toward the inside of the matt board. Adjust the box cutter so it is longer than the width of your straight edge and cut the matt.

This method is much more prone to error but it will work. You will notice that the mounting corners are peaking out of the matting. Make a note of how much is sticking out with a pencil and remove the visible part using the box knife. Make sure to remove the picture before you start cutting the corners. Remember the two strips that we glued to the top of our picture?

Now is the time to apply glue to the underside of those strips and glue them to the mounting board. If you ever need to remount the picture, you simply have to cut these strips to remove the picture from the frame. If the wood you acquired doesn't already have one, rabbet off what will be the inside bottom corner of the board.

If using a straight board, make sure to put the rabbet on the least attractive side of the board. A miter is a 90 degree joint formed by cutting each board at a 45 degree angle. This is the most common joint for picture frames, though other joints are sometimes used. Orient the board so that the board is perpendicular to you and the rabbet is face up and away from you.

Make a mark from the bottom left corner to the top of the board at a 45 degree angle. This will help you avoid cutting it wrong later. Using a miter saw, miter box, table saw or some other accurate cutting method, cut off the corner along the line you made.

Use a piece of sand paper to clean up the edge. This next step is a little difficult to explain but it is very important. The object is to measure the board for the next cut such that when they are assembled later, the mounted picture, glass and all the rest will fit. The trick here is that you want to measure from the bottom edge of the rabbet see picture. Mark the diagonal as before only this time the angle goes the other direction. Once you have one of the boards cut, use it as a template for the other board to insure that both of your lengthwise boards are exactly the same size and the widthwise boards are exactly the same size.

Now it is time to put the four pieces of wood together into your frame. Get out your corner clamp and clamp a length piece and a width piece together. If you are planning to use wood glue, apply the glue to the edges of both boards before putting them in the clamp. The clamp isn't completely necessary but it does guarantee that the frame will be square even if your miters are not perfect. It also holds the pieces together while you are pounding on it in the next part.

Get a joint fastener and place so half of it is on one piece of wood and the other half is on the other. Pound the fastener in all the way using the hammer. Take the other two pieces of wood and assemble them in the same manner.

Make sure you attach the boards on the right sides this time. I do this by lining them up with the other two boards to dry fit the frame.

Also, make sure that you are lining the boards up so all the rabbets are on the same side and you are nailing in the joint fastener on that side see picture. Finally, attach the two remaining corners in the same manner. Once the frame is assembled, make sure the picture, glass and the rest fit in the rabbet.

There should be a little bit of extra room to allow for changes in size due to humidity. It absolutely should not be so tight that the picture warps in order to fit. Alternately you can use a chisel to make the rabbet a little larger. Obviously it is best to have it be the right size to begin with. It is very difficult to create perfect miter corners. If your corners have gaps, you can use some wood filler to fill the gaps.

Let the wood filler dry and sand the frame. Finally finish as desired. In my case, I apply two coats of primer and two coats of glossy black enamel. You do not need to finish the back of the frame if you don't want to. Almost done! Now all that is left to do is mount the picture into the frame.

Place the frame back side up. First drop in the glass, making sure the glass is very clean and dry. Next drop in the matt board, followed by the mounted picture board. Make sure to put the latter two How To Make A Frame With Vinyl Mac in upside down i. Now that everything is in place, use glazing points to keep it from falling back out again. Just use a large flat screw driver and push the points into the wood. I really want to make a picture frame with something 'mouth of context' I ended up doing something similar, except I had a few more tools at my disposal.

I used a table saw and miter gauge to make the sides out of oak, and then used a router table to shape the edges. I also used a band clamp for the glue-up rather than gluing each corner individually, although I can see how that method might be preferable for such a large frame. Slightly more work but it's visually appealing and very strong.

Another alternative that may turn out to be most cost efficient is to purchase a custom frame online. A site like www. Cost varies by moulding style and width. They chop, route, and wedge your custom sized frame and FedEx it free the next day. Make you own frames if you enjoy doing it, not if your sole purpose is to save money. Once you factor the cost of materials, storage, tools, waste, your time, and the occasional goof up; the cost is actually quite high. Reply 6 years ago on Introduction.

Even if I have to buy some of the tools I bet this is the economical choice for me. That said, if I do go through with this I will probably get a mat professionally cut. Many places that sell mats will cut them for very little six dollars maybe , and I have shaky hands. A homemade frame that's simple and has an imperfection or two is something to be proud of, but a crooked mat will drive me crazy. Millimeters rule. Don't believe it? Try reading fractions of an inch off of a ruler.

Good luck. I've seen clerks in a framing shop get it wrong. Inches are completely unsuited for precision measurements. Cool frame work! At this point in the process I like to glue a sheet of paper across the back of the frame to help prevent dust from finding it's way in.

You can help keep the metal straight edge from moving around and messing up your cut! If it's a long straightedge, tape it and the matt board to be cut to the work surface with some blue masking tape. And believe me you WILL notice that goof every Make A Frame With Illustrator Css time you look at the picture. I concur with longouyang. When you're writing instructions like this, it's important to spell words like 'rabbet' correctly.

Reply 13 years ago on Introduction. You've given very clear directions, and it's nice to see the awknowledgement that something should be done to protect the image from the acid in the framing materials -- but the acid free paper used is hardly going to do anything against the high acidity materials used here. I know you didn't claim it would last forever, I'm just pointing it out so people are aware.

A few months ago I got a couple of gorgeous art prints from Minted. The first one I created a frameless, floating mount for and hung it in my bedroom.

The second print, is massive! There was no way I was going to pay the money for a custom frame, so I decided to make a real, high quality frame myself. I found a few different tutorials for making a large picture frame, but I wasn't satisfied with any of them. Either they were built too flimsy, required special tools like a router , or didn't accommodate a sheet of real glass.

I'm really happy with the solution I came up with. It was easy to build, sturdy, and is a full fledged frame, with a groove for a heavy sheet of glass. Materials List. This frame could be made in any size! I made mine huge, but you could use this technique to make a smaller frame too.

Ready to get building? Pin the image below to save the idea for later. Let's be friends! Follow along, so you never miss a post. Newer Post Older Post. Unknown August 4, at AM. Subscribe to: Post Comments Atom. Follow By Email Receive posts straight to your mailbox!

Popular Posts. This post contains affiliate links.



21 Inch Tool Box Drawer Slides To
Best Woodworking Table Top Jacket
Rolson Wood Turning Chisel Set Off