19.07.2020  Author: admin   Diy Wood Projects To Sell
Then I saw the Jet Amazon Second Chance Pass it on, trade it in, give it a usdd life. I wanted a machine that was heavy enough so blanks that were severely out of round or blanks of uneven density would not cause the lathe to vibrate excessively. Up for auction is used jet 1442 lathe for sale result nice condition south bend lathe works wrench for a lathe or resullt. Simply pull the handle out slightly and move it to select,,or PRM. Details: jwl-vs, wood, lathe, manual, owners, operators, includes, sections, operation, wiring.

The Jet comes pre-wired for volts but it can be re-wired for volt operation. I also liked the fact that both the headstock and tailstock used MT-2 taper centers, and that the tail stock center travel was specified to be 4 inches.

I first saw the jet in the showroom of the local Quality Woodworking store and I was very impressed. It was a great deal more massive machine than pictures on the internet would suggest. I left the show room with a fairly high interest in this machine. My interest was tweaked further when Amazon. My interest was heightened even further after reading all of the very positive 4 star and 5 star reviews on the Amazon website by people who had recently purchased this machine.

I finally made the decision to buy this bad boy after I checked my back issues of American Woodworker and found a product comparison article for lathes in the January edition pages This article featured several of the attributes, which proved to be very informative and helped me to better understand the quality of the machine.

In all my pre buy research, I did not come across a single negative associated with this lathe, so I took the leap and purchased it. Every so often a good deal comes our way. In this case, this was my good deal. The tool rest, headstock and tailstock came attached to the lathe bed. The entire lathe assembly was wrapped in a very thick plastic cover and packed in one carton.

The carton consisted of a well built wooden pallet with a hardwood moisture proofed bed on top. The lathe bed was bolted to the moisture proof bed. The pallet was surrounded by heavy gauge cardboard.

Extra thick cardboard stiffeners were added to the inside of the package and then the box was banded to the pallet with two steel bands. The carton was marked as being pounds gross weight.

They were so sturdy I decided to keep them and use them as protective pads for the top of my work bench. The two legs were shipped in a separate heavy card board carton. They were each embedded in thick molded Styrofoam and packaged one on top of the other. This carton was marked as being pounds gross weight. The delivery truck had a lift gate and a hand operated battery powered forklift.

The driver unloaded both cartons and wheeled them into my shop. Because the lathe reached my door step in perfect condition, and since this was the best delivery service I had ever experienced with heavy tools of this type, I gave the driver a big tip, and it was worth it. If you buy this big boy I strongly suggest you have the help of one other person to assemble it.

In my case, I just couldn't wait for another person so I did all the assembly myself. The assembly itself is very simple. There are only 8 bolts and 4 adjustable feet to install. What makes it difficult is the extreme weight of the lathe.

There are a couple of tricks I used to get around the weight issue. First I opened the carton that contained the legs. I turned it on end so the legs were standing vertical, and then pulled each leg out by rocking it forward and out of the carton.

The legs are balanced enough to stand on their own so I left them standing on the side of the shop. I then removed the cardboard sides from the lathe carton, which gave me room to remove the tail stock, the tool rest and the head stock from the lathe bed. I then removed the lag bolts that held the bed to the shipping pallet.

I lifted the lathe bed up onto the roll around and used it to roll the bed to the area of the shop where the lathe was to be located. I then added the adjustable feet to the legs and teeter-walked them into position beneath the lathe bed. I then bolted the legs to the lathe bed, and removed the roll around.

I used two levels placed on the lathe bed, at 90 degrees to one another, and a hydraulic floor jack to raise first one end of the lathe then the other to adjust the feet for level. The floor jack made this leveling operation fast and easy. I used mineral spirits to clean all the machined cast iron areas of the bed, head stock, tail stock and tool rest, and then I applied a light coat of Johnson and Johnson paste floor wax to keep these areas from rusting.

I then attached the very heavy headstock, the tool rest and the tailstock, plugged it in and verified it worked. Tomorrow morning my back will tell me if I should have had the help of a second person. After I installed the drive center and spur center I moved the tail stock as close to the head stock as possible until the centers were almost touching one another.

I had hoped that the center pins of the two centers would line up perfectly but they did not. I'm not sure how to adjust this and right now I'm not even sure if an adjustment is called for. I think I will seek out more experienced opinions before I do anything. After the column was turned I wanted to be able cut the column in half lengthwise to produce two identical half columns.

To accomplish this I needed to make the blank so it was easily separable lengthwise into halves. I milled down 4 pieces of poplar stock so that all were of identical size. I then made two glue ups, each consisting two pieces of stock, to form the two halves of the blank. I then glued the two blank halves together with a piece of heavy brown wrapping paper in between the two. The brown paper created a "weak" joint that could be easily split with a blade and mallet after the turning was complete.

When glue up was complete the blank weighed 38 pounds. I didn't want the blank flying apart when I started turning so for safety's sake I drilled 4 holes, 2 on each end in the flat part of the pommels and inserted 4, six inch lag bolts to add strength across the brown paper boundary and help hold the two section blank together.

I spent two days turning the column and two additional days of sanding it smooth. The finished column was close to being perfect. The two halves of the column remained glued together and there was only a minor indication of the two beginning to separate during the turning. I was concerned about turning such a heavy and long piece using just the head stock and tail stock centers.

I contemplated using a faceplate for greater strength but rejected that idea when I couldn't guarantee that I could get it exactly centered on the end of the blank. When turning pommels or coved ends on a column it is imperative that the Used Jet 1442 Lathe For Sale Yahoo blank be mounted dead center, other wise the square parts of the pommel and the round part of the column will be off center with respect to one another and it will result in a very noticeable error.

Fortunately the four spur drive center and the 60 degree spur center with bearings that are supplied with the lathe worked great. I had no problem at all with this heavy piece coming loose. During the turning of this heavy blank, there was absolutely no vibration in this very massive lathe. Before I started, I placed pencil marks on the shop floor that outlined the position of the lathe legs. When the turning was complete, the legs were still within the penciled outlines indicating the lathe had not moved even the slightest amount.

Since I did not have to add any extra sand bag ballast to keep the lathe steady, this really made my day, and validated my decision to purchase this heavy machine over one of the lighter models. I added the flutes to the column using a home built jig consisting of a cradle to hold the round column, with a router table and guide on top. I used a plunge router to route a flute the length of the column and I repeated this every 20 degrees around the column circumference.

I simply rotated the column in its cradle until the flute line lined up with the center line of the router guide and then made the cut, and then repeated the procedure until all flutes were cut. I removed the 4 lag bolts and split the column lengthwise into two identical halves by forcing a thin blade in the brown paper intersection of the two column halves.

Check out the pictures of this lathe and column in the "User Supplied Pictures" section below Amazon's picture of the lathe. Other features to note about this lathe are: 1. The headstock has 12 holes on the spindle spaced at 30 degree intervals, and three threaded holes spaced at 20 degree intervals in the headstock casting. Using the supplied threaded indexing pin and a combination of these two sets of index holes allows the user to rotate and lock the piece mounted on the lathe in 10 degree increments.

The lathe has a variable speed control that can be adjusted when the lathe is turning. Variable speed is accomplished by changing the diameters of the motor and head stock belt pulleys, effectively changing the "gear" ratio between the two.

The headstock slides the entire length of the bed and can be rotated a full degrees for turning bowls or blanks larger than 14 inches. The lathe comes with a tool rest extension for turning bowls. During the time I spent on this column project, I got to know and feel comfortable with this lathe. I am glad I invested the effort researching lathes because I'm pretty sure that I ended up with a high quality machine that will provide years of heavy duty use and more than likely will never have to be replaced by a "better machine".

Would I buy this lathe again? The answer is a definite yes. Images in this review. This is a great addition to any woodworkers shop and is very easy to setup and use but the workmanship in this Jet product is below par. After two months I noticed the base was starting to rust so I immediately disassembled it and repainted the base before the rust got out of hand. This could have been prevented at the factory by using a good rust proof paint. After less than 5 hours of turning the adjustable pulley mounted on the motor came loose and had to be reinstalled properly.

Once I got all the problems straightened out that quality control should have corrected this wood lathe is a great addition to my shop. Of the three Jet products I own, Jet shaper, Jet bandsaw and Jet wood lathe , the workmanship in this item is the worst of the three. Although it does have some very good features, it also has some serious drawbacks which potential buyers should be aware of.

The worst feature, from a design perspective, must be the position of the motor. Mounted to the right of the mechanism i. This is especially evident when reverse mounting a large partly turned bowl, where the chuck is expanded into the interior of the rough turning.

I have to use a spindle extender to clear the motor, a work-around not needed on most other lathes. There is also a problem with the banjo design. Instead of being cast Used Wood Turning Lathe For Sale Near Me 01 entirely in iron, these banjos have a steel end plate, secured with 4 cap screws.

The problem is that the screws create a weak point, such that under heavy use, such as roughing bowls from large, oddly-shaped blanks, the screws break the cast iron.

I do use it hard, to rough bowls from roughly-rounded log sections, and have broken that casting once so far in the process. Also I should add that though I've gotten the spare parts I've needed, and so far quickly enough, ordering them has been problematic. Don't even bother to use their web site to order parts.

It let me complete the entire process, then rejected me at the very end without any explanation. When I phoned in my order, their service rep acknowledged that it fails to work at least half the time. Several months later : no change. Contact them by phone if you want to save some aggrevation. Other minor issues are that the 1 HP motor is not powerful enough, tending to stall frequently when turning large items aggressively or even less aggressively.

The stepped speed control is convenient compared with belts, but the lowest speed, rpm, is not as slow as I'd like for some bowl turning. And this machine is not really heavy enough to turn large off-balance blanks without being bolted to the floor - not a biggie since I did that, and a common enough issue with many lathes. The spindle runs in multiple high-quality ball bearings that are responsible for its smooth running as well as a long life.

The spindle also has the virtually standard 2 Morse taper within the snout that will accept virtually any modern accessory. You can also use this through hole for auger boring lamps and similar projects. A screw-in pin can be installed in one of three positions on the spindle housing for extensive indexing capabilities. A descriptive chart in the user manual explains this capability completely. Simply pull the handle out slightly and move it to select , , , , , , , or PRM.

That is a very useable speed range that will handle virtually any job on a lathe. It is important to note that speeds must be changed with the lathe running as is common with mechanical speed controls. The motor is turned On and Off with an oversized paddle switch located on the front of the headstock. The tool rest base is a big chunk of cast iron on its own but the bed portion has a low enough profile to prevent interference with all but the biggest work pieces.

The locking lever is long enough to give you plenty of leverage to lock the base in place without strain. The tool rest has its own repositionable locking lever. JET includes a cast iron tool rest extension that provides additional reach for when you run into the odd job or turn a large piece off the bed. This extension fits right in the tool rest base and the tool rest then mounts in the extension.

The tool rest extension isn't something you will use all of the time but it is worth its weight in free mahogany when you need it. The tailstock is another place that JET piles on the cast iron to insure rigidity. The spindle has a 2 Morse taper that automatically ejects whatever tooling is in it when the spindle is fully retracted. That 2 Morse taper also makes it compatible with lots of aftermarket accessories. JET just saved you some time and probably a little money. Thanks to my trusty 2-ton hoist I was able to assemble this machine without injury.

However, because of the heft of all that cast iron you need either a hoist or a few buddies to get this done safely. I checked the center-to-center alignment and that came out as close to perfect as I can see without the aid of a microscope.

I also tried pivoting the powerhead to all of its presets and then back to zero and the center-to-center alignment returned as well. I should note that because this is a Reeves-style drive you can only change speeds while the machine is running.

If shifting on the fly is a hassle for you the only real option is to step it up pay more and get a machine with an electronically variable speed control. The tailstock and tool rest groups performed fine throughout the evaluation. Their oversized handles make locking these components in place on the bed a no-strain chore. Motor power is more than adequate for this size lathe.

Regardless of the RPM setting or the piece being turned I never felt lacking for power. This motor actually surprised me a little with the amount of power available at lower RPM. If my previous history with JET equipment is any indication you can expect a very long service life from this machine. It is built very well and the only vibrations I encountered came from badly out of balance wood, not from the lathe itself.



Carter Circle Cutting Jig 10
Scroll Saw Machine Price Yahoo
Projects To Build With C Jacket