24.03.2021  Author: admin   Simple Wood Craft Ideas
USD 3. I like Varathane's Matte Soft Touch for projects like this. Before I get too deep into the build details, I want to acknowledge that my design woodwor,ing just a copy of Line Phono's original turnable stand. More on that later. This will help to keep the plywood intact and keep the block from spinning when the hole saw woodworking plans record cabinet model through the plywood.

I came to the conclusion that the initial iteration is better suited for a CNC machine or laser cutter. I've included that design in Adobe Illustrator format for anyone wanting to take a crack at making the stand through other means.

I scrapped the first set of drawings and took a simpler approach for subsequent drafts. I settled on a plan that is much simpler and easier to build even though I lost some of the 16000 Woodworking Plans Review Model design aesthetic that attracted me to LP's stand in the first place.

Or if you go the route I did and Woodworking Plans Record Cabinet Cabinets used smaller, 2' x 4' panels, you're good to go. If this is your first time working with plywood know that it is notorious for tearouts. There are a couple of things you can do to stop that from happening and ruining a nice sharp edge. I won't go into depth here because there are plenty of tutorials on minimizing tearout on the net, like this one.

If you are cutting down a 4' x 8' sheet, don't forget to take into account the thickness of the blade when you are measuring. If you mark the entire sheet with cut marks ahead of time and cut on those marks, you'll wind up with panels that are too narrow due to the kerf. I suggest cutting the back panel first, which is 24" wide x The panel for the legs is the same size at 24" wide x These will be the shelves. At the end of this step you will have two identical legs and a back panel that will mount to the shelves.

The pink dotted lines in the PDF show where the edges of the shelves meet with the back and leg panels. Be sure to mark the locations of the shelves because it will help when the time comes to put everything together. I Woodworking Plans Bookshelves Model provided the measurements from the bottom of the panels to the underside of each shelf. It takes some time to transfer the measurements, but it's a necessary step. If you want to keep tearout to a minimum, tape the surface of the plywood where the hole saw meets the wood and place a block of wood directly below where you will be drilling.

Make sure you clamp the panel and block to a workbench or sawhorse or whatever surface you're working off of. This will help to keep the plywood intact and keep the block from spinning when the hole saw punches through the plywood. In case you are wondering why I made the shelves such an odd width, I did it because of the thickness of the plywood.

I wanted to make the entire stand 24" wide. I bring up this important point for one reason. That's much easier to mark and cut. Lay the back panel flat on your work surface and drill the pilot holes and countersink all of them. Next, drill and countersink the legs as well.

I started by attaching the legs to the back panel. Stand up the back panel and one of the legs. Be sure to put the sides with the countersinks on the outside. If you don't have a clamp, have a friend hold the pieces in place while you screw in the 8 screws.

Repeat for the opposite leg. This part is tricky. I started with the top shelf since the unit is already standing up, but you can start wherever you choose. If you have long clamps, now would be the time to use them. Apply glue to the three edges of the shelf that are going to attach to the legs and back panel.

Use the guidelines on the inside of the stand to line up the first shelf. Clamp it, screw it in place, and repeat for the remaining shelves. With the unit assembled, it's time to plug those drill holes, sand the entire thing, and apply a finish.

I actually left mine raw until I have the time to sand and put a coat of Varathane on it. Reply 3 years ago. Reply 4 years ago. I'm not sure why you aren't able to download the Illustrator files. PM with your email address—I'll send them to you. Well I'm not quite done, but I wa so pumped with the progress towards your first design that I wanted to share.

All done with basic power tools. What tools did you use to cutout the parts? Are you having any problems with the parts fitting too tightly, because I didn't leave a whole lot of wiggle room. Man, I can't believe how awesome your stand is looking! I used a jigsaw mainly.

I read a few other posts on here about measuring saw offsets and clamping off fences so that's what I did. Clamped a level and used it as a fence for each cut. Free handed the large radius curves with the jigsaw, and used a palm orbital sander to create the smaller radiuses. I went to kinkos and had your plans printed to scale and then used 3M 77 glue to apply it to the MDF and then just used it as a template. Using the templates, as long as my cuts were near perfect, your spacing was dead on.

I just tried to leave it on the snug side and then test fit, and sanded where needed. I estimate it can hold around records. Please post some photos if you do make your own stand! The stereo receiver was made by Fisher in the s. The model number is Fisher also made the and series in addition to the I love your design.

I would like to try a hybrid of the first draft plans with the final. For Fun , For the Home , Furniture. I ordered some hair pin legs and designed a stand with storage for records and a table top for the player. While I was at the hardware store I also picked up some of this Bandit iron on tape that has a wood finish, perfect for the edge of plywoods.

Next I wanted to show you how to use the iron on tape to cover the edges. This is actually made out of real wood and can be used pretty easily. Just measure out what you need and cut it with scissors. I like to start in the middle and get it to attach. You want to avoid burning the wood. I use a razor blade to trim the excess tape off of the edges. I also try to smooth that out after by sanding lightly with grit sand paper. I inserted the dowels, slightly glued, over top of the holes.



Woodworking Projects For Infants Youtube
Build A Toy Castle 42
Wood Workshop Wellington 6th